ACCULOGIC, INC.

SIDE-4/ PLUS

  Data bus:                  16-bit, ISA

  Size:                      Half-length, full-height card

  Hard drives supported:     Two IDE(AT) drives

  Floppy drives supported:   Two 360KB, 720KB, 1.2MB or 1.44MB drives

[Image]

                            CONNECTIONS

                   Function                          Location

  34-pin control cable connector-floppy drive           J1

  4-pin connector-drive active LED                      J2

  40-pin AT Interface (IDE) connector                   J3

  9-pin serial port 2-internal                          J4

  15-pin game port-internal                             J5

  9-pin serial port 1-external                          J6

  25-pin parallel port-external                         J7

                        USER CONFIGURABLE SETTINGS

               Function                    Location           Setting

  »   I/O Channel Ready signal               JP4               open
      disabled

      I/O Channel Ready signal               JP4              closed
      enabled

  »   Floppy drive enabled                   JP5             pins 1 & 2
                                                              closed

      Floppy drive disabled                  JP5             pins 2 & 3
                                                              closed

  »   Floppy drive port address is           JP6             pins 1 & 2
      3F0-3F7h                                                closed

      Floppy drive port address is           JP6             pins 2 & 3
      370-377h                                                closed

  »   Single speed floppy drives             JP7             pins 1 & 2
      supported                                               closed

      Dual speed floppy drives               JP7             pins 2 & 3
      supported                                               closed

  »   Hard drive enabled                     JP8             pins 1 & 2
                                                              closed

      Hard drive disabled                    JP8             pins 2 & 3
                                                              closed

  »   IDE select mode enabled                JP9             pins 1 & 2
                                                              closed

      Not used                               JP9               open

  »   Hard drive port address is             JP10            pins 1 & 2
      1F0-1F7h                                                closed

      Hard drive port address is             JP10            pins 2 & 3
      170-177h                                                closed

  »   Not used                               JP11              open

  »   IRQ14 normal                           JP12            pins 1 & 2
                                                              closed

      IRQ14 delayed until ACTIVE-            JP12            pins 2 & 3
      signal is removed                                       closed

                   SERIAL & PARALLEL PORT CONFIGURATIONS

              Function                    Location            Setting

  »   Serial port 1 (CN6) enabled           JP13             pins 1 & 2
                                                              closed

      Serial port 1 (CN6) disabled          JP13             pins 2 & 3
                                                              closed

  »   Serial port 1 (CN6) set to            JP14             pins 1 & 2
      COM1                                                    closed

      Serial port 1 (CN6) set to            JP14             pins 2 & 3
      COM3                                                    closed

  »   Serial port 2 (CN4) enabled           JP15             pins 1 & 2
                                                              closed

      Serial port 2 (CN4) disabled          JP15             pins 2 & 3
                                                              closed

  »   Serial port 2 (CN4) set to            JP16             pins 1 & 2
      COM2                                                    closed

      Serial port 2 (CN4) set to            JP16             pins 2 & 3
      COM4                                                    closed

  »   Parallel port (CN7) enabled           JP17             pins 1 & 2
                                                              closed

      Parallel port (CN7) disabled          JP17             pins 2 & 3
                                                              closed

  »   Parallel port (CN7) address           JP18             pins 1 & 2
      is LPT1                                                 closed

      Parallel port (CN7) address           JP18             pins 2 & 3
      is LPT2                                                 closed